4L60E (700R4) Rebuild Manual DP0 (AL4) Repair manual ZF 6HP19/21 Repair manual 09G TF60SN Repair manual 5R55S/5R55W/N Repair manual U660E/U760E Repair manual A500/40RH/42RH/42RE Repair manual 722.9 Repair manual 722.6 repair manual A518/A618 Repair manual ZF5HP19 Repair manual 02E DQ250/DQ200 Repair manual 42LE/42RLE/A606 Repair manual. Presented for the sale Technicians Diagnostic Guide ZF 4HP-18 FLE & FLA is a diagnostic software for vehicles, which contains full information on repair and maintenance of vehicles, as well as detailed technical information on solenoid resistance check, the application of electromagnetic clutches, the breakdown of the valve body, the retainer and verifying the location details, location.
ZF 5HP18 Transmission Repair Manual PDF free online
This manual contains precise details of how to repair the complete transmission.
- Transmission repair manuals ZF 4HP18 Information about rebuild transmission ZF 4HP18 Reliability of transmission ZF 4HP18 was combined with its simplicity and ease of use. Optimized gear ratios made it easy to implement dynamic indices not only for small-volume engines, but also for power units of 3 liters and more.
- How do I find service and parts support for my ZF or Mathers pneumatic controls and shaft brakes? Northway Products now handles all sales and support for pneumatic controls and shaft brakes. You can go to www.northwayproducts.com, or contact them at [email protected] or 425-493-1127.
- ZF Transmission Service Manual 5 2 Transmission System 2.1 Transmission Introduction 2.1.1 General Overview of the Transmission The ZF power gearshift transmission is composed of the hydraulic torque converter and rear-mounted countershaft transmission with multi-sheet friction clutch.
A1 dismantling and assembly work is described in the correct order.
The photographs have been selected to cover various types of transmission and may therefore differ from the vehicle on which you are working.
The component list precisely defines which version of the transmission you are working and this is also reflected In the parts list.
If any major modifications have to be taken into account when repairs are carried out, you will be notified by Technical Bulletin.
Depending on the nature of the fault, It may be possible to limit the repair to the actual components and areas of the transmission that have failed.
Repair Manual For Dodge Intrepid
In this connection, please note:
Haynes Repair Manual
- Always renew the pistons if there is a fault on clutch F or brake G. Never re-use seals, for example 0-rlngs and shaft sealing rings.
- If the transmission has been run for a considerable distance (> 50.000 km), renew all lined and steel discs.
- If clutch damage has occurred the converter, oil cooler lines and the oil cooler itself must be thoroughly flushed out with a suitable cleaning agent.
The following conditions must be satisfied:
- The necessary special tools must be available The complete set Is listed in Section 1.8 of this manual.
- A suitable transmission test rig should be available.
Refer to the Technical Bulletins for the relevant test values.
CONTENTS
Preliminary information
- 1. General remarks
- 1.1 Drawing of transmission
- 1.2 Power flow schematic
- 1.3 Oil flow charts
- 1.4 Adjustment work
- 1.4.1 Release clearance at clutch F (snap ring)
- 1.4.2 Release clearance at brake G (snap ring)
- 1.4.3 Release clearance at brake D (snap ring)
- 1.4.4 Clearance at output side (washer)
- 1.4.5 Release clearance at clutch E (snap ring)
- 1.4.6 Release clearance at clutch A (snap ring)
- 1.4.7 Release clearance at brake C1 (snap ring)
- 1.4.8 Transmission axiale clearance (washer)
- 1.4.9 Release clearance at brake C2 (two washers)
- 1.5 Tightening torques
- 1.6 Troubleshooting (faults, causes and remedies)
- 1.7 Checking the transmission
- 1.8 Special tools
- 2. Dismantling
- 2.1 Dismantling according to assembly groups
- 2.2 Output side
- 2.3 Planetary gears, complete
- 2.3.1 Planetary gear set III
- 2.3.2 Clutch F
- 2.3.3 Brake DG with 1st gear freewheel
- 2.4 Input side
- 2.4.1 Clutch E
- 2.4.2 Clutch A
- 2.4.3 Clutch B and 3rd gear freewheel
- 2.4.4 Brake C
- 2.5 Oil supply unit with brake C
- 2.6 Housing with shift and parking pawl
- 3. Assembling according to assembly groups
- 3.1 Housing with shift and parking pawl
- 3.2 Planetary gear set, complete
- 3.2.1 Planetary gear set III
- 3.2.2 Clutch F
- 3.2.3 Brake DG with 1st gear freewheel
- 3.3 Output side
- 3.4 Planetary gear sets I and II
- 3.5 Input side
- 3.5.1 Clutch E
- 3.5.2 Clutch A
- 3.5.3 Clutch B and 3rd gear freewheel
- 3.5.4 Brake C
- 3.6 Oil supply unit with brake C
- 3.7 Selector unit, oil sump and converter
Language: English
Format: PDF
Pages: 121
Format: PDF
Pages: 121